LaserAI
The complete guide

Install AI on any laser.
Burn it right the first time.

Turn a shaky, scrap-prone machine into one that gets it right the first time, every time. Not a theory: this is the exact method running a real fiber MOPA shop, written down step by step, with the mistakes included so you do not repeat them.

Get the guideI have a code

What an AI on your laser actually does

The laser keeps working exactly as it does today. The AI sits next to it and does the tedious, error-prone parts.

01

Builds the job

Generates the project file from your artwork at the true size, centered, flipped the right way, with the right layers. No hand-placing, no upside-down photos.

02

Checks before it burns

Reads the machine's state, verifies the loaded file, and refuses to start unless everything matches. It cannot talk itself past a safety rule.

03

Measures the result

Scan or photograph the piece and it measures the real dimensions and tells you what is off, then corrects the next run. Calibration with a flatbed scanner.

04

Learns your material

Runs the test grids, reads the results, and keeps the settings that worked, so the next job on that metal starts from proven numbers.

05

Runs from anywhere

Plain one-line commands over any remote shell. No screen sharing, no clicking, nothing that breaks when a window moves.

06

Keeps a record

Every file, setting and result is on git and in plain notes, so the shop remembers what worked months later.

The savings are in "right the first time"

A laser does not forgive. The cost of one wrong burn is the part, the blank, the hour and the retry, and it repeats.

Doing it by hand

  • Photo burned upside down or inverted
  • Settings that were never applied
  • "Close enough" size, rework later
  • Same mistake next month

With an AI that checks

  • File verified before the start command
  • Position, size and layers confirmed
  • Test patch first, then the real piece
  • Every lesson becomes a rule it follows
1 retry

On a $30 blank plus an hour of machine time, a single avoided redo pays for the guide several times over.

Any shop

The method works on any galvo or fiber laser that runs LightBurn-class software. One setup, then it carries over.

$25

One payment in SOL. No subscription. Lifetime access to the guide and its updates.

What is inside the guide

A full workup, in the order you build it. Every chapter was proven on a real machine; the details unlock with your code.

  1. The architecture in one pageWhat talks to what, and why a boring design is the safe one.
  2. Headless control: the command portThe seven commands LightBurn actually understands, and the three it does not.
  3. The laser CLIOne command per action, with the complete tested script.
  4. Remote control without screenshotsRun commands on the shop PC from anywhere, and move files both ways reliably.
  5. The safety layerThe nine rules every AI must follow, written as a prompt you can paste.
  6. Writing job files in codeCoordinates, bitmaps, layers, and the settings a generated file silently ignores.
  7. Calibrate with a scannerMeasure a burned sheet to better than your ruler, and correct the lens.
  8. Surface prep and color on stainlessMulti-pass angle strategy, swatch plates, how to read the results.
  9. The first-time-right checklistThe routine that stops the expensive mistakes before they happen.
  10. Our mistakes, so you skip themReal failures, what caused each one, and the one-line fix.
Safety first. A laser can start fires and cause permanent eye injury. The guide teaches an AI to load, check and report, and to start a burn only when a human has said so. You remain responsible for eyewear, extraction, fixturing and the machine's emergency stop.

Get the guide

Pay once in SOL. Your unlock code is emailed to you as soon as the payment confirms (usually under a minute).

$25 paid in SOL, one time
  1. Enter your email (the code is sent there).
  2. You get a fresh Solana address made just for your order.
  3. Send the exact amount shown. The page confirms it on-chain and emails your code.
Send exactly
to this address (made only for you):
Open in wallet
Waiting for your payment...

Send from your own wallet, not an exchange withdrawal that adds a memo. Quoted at . If you send slightly less, the page tells you how much more is needed. The address stays valid, so you can pay a little later too.

Already paid? Unlock

Paste the code from your email. The emailed link signs you in directly.

Questions

Which lasers does this work on?

Any laser you drive with LightBurn-class software, especially galvo fiber and MOPA machines (JCZ boards and similar). The principles carry over to others; the exact commands are for LightBurn.

Do I need to know how to code?

No. The guide gives you the scripts and the exact prompts. You need a PC next to the laser and an AI assistant that can run commands.

Is it safe?

The whole design is that the AI cannot start a burn on its own. Safety gets its own chapter and a rule set you give your AI verbatim.

Why pay in SOL?

It is instant, has no chargebacks and no account to create. You send from your own wallet to an address made for your order.

What if I lose my code?

Use "Email my code again" with the address you ordered with.